OTHER HARDWARE


HOME DOCUMENTATION SOFTWARE FIRMWARE HOWTOs TECHNOTES USEFUL TOOLS OTHER SOFTWARE OTHER HARDWARE VIDEOS MISCELLANEOUS FEEDBACK MORE G3NRW SITES

Updated 23 July 2018

This section contains links to non-Icom hardware that is either produced specifically for the IC-7300 or which supports several rigs including the IC-7300
 Title/LinkDateSupplierDescription
1MFJ ENTERPRISES 5213 plug and cable assemblyMFJOpen-ended cable wired to 13-pin DIN plug, for use with the IC-7300 ACC2 Connector
(The IC-7300 comes with a similar cable, but you may need another one)
2IMRAD RX7300InradINRAD model RX7300 allows you to add a receive-only antenna jack to the Icom IC-7300. This easy to install plug-in modification requires no soldering and is easily installed and easily reversible. The RX7300 can also be used for the insertion of accessory items into the receiver chain on the IC-7300 like receive-only bandpass filters, low noise preamps, etc. When installed, transceiver will transceive using the SO-239 antenna connector on transmit, and one RCA phono jack on the RX7300 on receive. To use transceiver in normal transceive operation, leave the RG-174 coax loop installed
3USB IsolatorU.S. Converters LLCIf you need to isolate your USB device from your computer this USB Isolator is an effective and easy solution to ensure total isolation between your USB devices and your computer. This USB isolator separates both the data lines and power supply from your computer, fully protecting your USB devices and data signals against electrical noise, high voltage spikes, surges and ground loops for up to 3000V, which otherwise easily could damage your equipment
4The Ten-a-Tuner for IcomBob, W2ENYSimply plug this device into the tuner jack and your radio will think there's an Icom antenna tuner attached. This activates the 'tuner' button on the front panel of the 706 series (works with others like the 7000, 708, 718, 746, 756, PRO, PRO II, etc.).
When the tune button is operated, the radio will transmit a 10 watt CW signal for approximately 8 seconds
5Monitor Sensors 630m TransceiverMonitor Sensors AustraliaThe Monitor Sensors 630m Transverter enables any Amateur Radio Station, equipped with a conventional HF transceiver, immediate, all mode, access to the new 472-479 kHz, 630m band
6Transverter Interface Kit for the IC-7300Kuhne ElectronicSimple transverter interface kit for the IC-7300
7Click2Tune for ICOMSOTA BeamsOur Click2Tune for ICOM systems provides you with complete and reliable control for transmitting a low-power tuning signal for tuning the antenna system.

It transmits a low power carrier (user selectable level on some radios) without any need to change the mode and for as long as you press the button - YOU are in control.

We worked hard on getting the ergonomics right so that it sits nicely in your hand and we even trialed three types of buttons before we found one that had the right size and "feel". We also made it look good to fit in with your shack.

It's a great accessory for any ICOM radio that supports their auto-tuner. Tested on: IC-7300, IC-7600 (ant. 1), IC-7100, IC-730, IC-746 (ant. 1), IC-9100 (ant. 1), IC-706 (all variants), IC-703, IC-746.

The Click2Tune for ICOM is available as a kit or ready built! We have also written great instructions (build time around 30 minutes)
8** NEW **
FA-AS
Automatic Antenna Selector (German)


FA-AS
Automatic Antenna Selector Construction Manual (English)
Funk AmateurAntenna selector kit for Icom Transceivers with one antenna
socket. For use with up to 4 separate antennas, each operating
frequency may be automatically or manually selected, also
with an optional transverter. Possibility of using separate
transmitting and receiving antennas
9** NEW **
Analog S-Meter PCB (Dutch)

Analog S-meter (YouTube video)
Communicatie CenterA cheap PCB for building a remote analog S-meter for the IC-7300 (and other Icom radios). The video shows the meter installed inside an LDG box for the purposes of demonstration, but the meter can be installed in any suitable box
10** NEW **
Wire Bale Desk Stand
Nifty Ham Radio AccessoriesA simple bit of hardware that elevates the front of the rig to a more readable angle

HOME DOCUMENTATION SOFTWARE FIRMWARE HOWTOs TECHNOTES USEFUL TOOLS OTHER SOFTWARE OTHER HARDWARE VIDEOS MISCELLANEOUS FEEDBACK MORE G3NRW SITES